欢迎来访济南共润科技有限公司官网!

济南共润科技有限公司

咨询服务热线
0531-88270327 13153168609
当前位置: 首页 - 新闻中心 >
新闻中心

滚珠丝杠防锈预防措施有哪些?

来源:http://www.jngongrun.com/ 日期:2020-09-23 发布人:admin

 影响金属腐蚀的主要要素。TBI滚珠丝杆和螺母是碳钢构造,腐蚀是由各种内在的和外在的要素所惹起的,归结起来主要有:①金属资料自身化学成分和构造;②金属外表光亮度(氧浓度差电池腐蚀);③与金属外表接触的溶液成分及pH值;④环境温度和湿度;⑤与金属外表相接触的各种环境介质。

  Main factors affecting metal corrosion. TBI ball screw and nut are carbon steel structure. Corrosion is caused by various internal and external factors. It can be summed up as follows: 1) chemical composition and structure of metal material itself; 2) surface brightness of metal (oxygen concentration difference battery corrosion); 3) solution composition and pH value in contact with metal surface; 4) ambient temperature and humidity. Degree; _Various environmental media in contact with metal surface.
  一,被防锈物的外表预处置
  1. Appearance pre-disposal of rust-proof materials
  1)外表清洁:清洗必需依被防锈物外表的性质和当时的条件,选定恰当的办法。普通常用的有溶剂清洗法、化学处置清洁法和机械清洁法。
导轨丝杠
  1) Appearance cleaning: Cleaning must be based on the nature of the appearance of the rust-proof material and the conditions at that time, select the appropriate method. The common cleaning methods are solvent cleaning, chemical disposal cleaning and mechanical cleaning.
  2)外表枯燥清洗洁净后可用过滤的枯燥紧缩空气吹干,或者用120~170℃的枯燥器停止枯燥,也可用洁净纱布擦干。
  2) After the appearance is dry and cleaned, it can be dried with filtered dry compressed air, or with a dryer at 120-170 C to stop the drying, or it can be dried with clean gauze.
  二,涂敷防锈油
  2. Coating antirust oil
  1)浸泡法:一些小型物品采用浸泡在防锈油脂中,让其外表粘附上一层防锈油脂的办法。油膜厚度可经过控制防锈油脂的温度或粘度来到达。
  1) Soaking method: Some small articles are soaked in rust-proof grease, so that their appearance is adhered to a layer of rust-proof grease. Oil film thickness can be achieved by controlling the temperature or viscosity of rust-proof grease.
  2)喷雾法一些大型防锈物不能采用浸泡法涂油,普通用大约0.7Mpa压力的过滤紧缩空气在空气清洁停止喷涂。喷雾法适用溶剂稀释型防锈油或薄层防锈油,但必需采用完善的防火和劳动维护措施。
  2) spraying some large antirust substances can not be used to soak the oil, usually with about 0.7Mpa pressure filtration compressed air in the air cleaning center to stop spraying. Spray method is suitable for solvent dilution antirust oil or thin layer antirust oil, but must adopt perfect fire protection and labor maintenance measures.
  3)刷涂法用于不适用浸泡或喷涂的室外建筑设备或特殊外形的制品,刷涂时既要留意不产生堆积,也要留意避免漏涂。
  3) Brushing method is suitable for outdoor construction equipment or products with special shape which are not suitable for immersion or spraying. When brushing, we should pay attention not only to avoid accumulation, but also to avoid leakage.
  以上是导轨丝杠制造商为大家整理的相关内容,想要了解更多内容,欢迎访问网站:http://www.jngongrun.com
  The above is the relevant content of the guide screw manufacturer for you. For more information, please visit the website: http://www.jngongrun.com.

济南共润科技有限责任公司