2) The guide screw manufacturer reminds you to avoid mixing different lubricants. Even lubricating greases with the same thickener may have adverse effects on each other due to different additives.

3）要在经常产生振动的场所、无尘室、真空、低温或高温等特殊环境下使用时，请使用符合规格?环境的润滑脂。

3) When using in places that often generate vibration, clean rooms, vacuum, low or high temperature special environments, please use those that meet the specifications? Environmental lubricating grease.

4）对无油嘴和润滑孔的产品进行润滑时,将润滑剂直接涂抹到滚动面上,以行程长度为单位进行数次跑合,使润滑脂进入产品内部。

4) When lubricating products without nozzles or lubrication holes, apply the lubricant directly to the rolling surface and run in several times based on the stroke length to allow the grease to enter the interior of the product.

5）润滑脂的稠度随温度而变化。滚珠丝杠的扭矩也随稠度而变化,请注意。

5) The consistency of lubricating grease varies with temperature. The torque of the ball screw also varies with the consistency, please note.

6）加脂后润滑脂的搅拌阻力,可能会导致滚珠丝杠旋转扭矩增大。请务必进行跑合运转，将润滑脂进行充分跑合后，运转机械。

6) The stirring resistance of the lubricating grease after greasing may cause an increase in the rotational torque of the ball screw. Please make sure to run in and fully run in the lubricating grease before operating the machine.

7）加脂完成后,多余的润滑脂有可能向周围飞溅,请根据需要进行擦拭。

7) After the greasing is completed, excess grease may splash around. Please wipe it as needed.
导轨丝杠

8）润滑脂随着使用时间的增长,性状劣化,润滑性能降低,所以需要根据使用频率点检并补充润滑脂。

8) As the use of lubricating grease increases, its properties deteriorate and its lubrication performance decreases. Therefore, it is necessary to check and supplement the lubricating grease according to the frequency of use.

9）根据使用条件和使用环境不同,加脂时间间隔不同,请以每运行100km（3～6个月）为基准进行加脂。请根据实际设备,确定终的加脂时间间隔和加脂量。

9) According to different usage conditions and environments, the interval between greasing times varies. Please use every 100km (3-6 months) of operation as the benchmark for greasing. Please determine the final greasing interval and amount based on the actual equipment.

10）安装方式和丝母的润滑孔,可能致使润滑油不循环造成润滑不良,设请进行充分探讨。

10) The installation method and lubrication hole of the screw nut may cause non circulation of lubricating oil and poor lubrication. Please fully explore this during design.

总之，使用滚珠丝杠时,必须提供良好的润滑。如果以无润滑状态直接使用,可能会加快滚动部分的磨损,因而其使用寿命会缩短。更多相关事项就来我们网站http://www.jngongrun.com咨询！

In short, good lubrication must be provided when using ball screws. If used directly without lubrication, it may accelerate the wear of the rolling part, thus shortening its service life. For more related matters, come to our website http://www.jngongrun.com consulting service

上一篇：有可能会影响联轴器正常运转的因素
下一篇：主轴组件发生故障怎么办？