欢迎来访济南共润科技有限公司网站!

济南共润科技有限公司

咨询服务热线
0531-88270327 13153168609
当前位置: 首页 - 新闻中心
新闻中心

滚珠丝杠在安装时如何操作的?

来源:http://www.jngongrun.com/ 日期:2020-07-08 发布人:

1、滚珠丝杠属于精密传动装置,必须进行润滑。在螺母内使用家皂基润滑脂1-3号透平油润滑。山东博特精工股份有限公司网站|滚珠丝杠|直线导轨|主轴 1.滚珠丝杠属于精密传动装置,必须进行润滑。在螺母内使用家皂基润滑脂1-3号透平油润滑。

1. Ball screw belongs to the precision transmission device and must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts. The official website of Shandong Bote Precision Industry Co., Ltd. ball screw linear guide shaft 1. Ball screw belongs to precision transmission device, which must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts.
2.滚珠丝杠与滚动轴承一样,混入灰尘异物将会降低使用寿命。因此,必须采用丝杠保护套加以保护。国内外各种类型的滚珠丝杠副大部分均已安装有迷宫式密封环,防止赃物进入滚珠丝杠体内。另外,在金属屑易侵入丝杠的场合使用时,还应考虑在丝杠全长上采用丝杠保护套防护。
2. Like rolling bearing, ball screw mixed with dust and foreign matters will reduce its service life. Therefore, it is necessary to use the lead screw protective sleeve to protect it. Most of the ball screw pairs at home and abroad have been installed with labyrinth seal ring to prevent dirt from entering the ball screw. In addition, when the metal chips are easy to invade the lead screw, the screw protective sleeve should be used in the full length of the lead screw.
3.由于滚珠丝杠螺母的特殊结构,不宜承受径向负荷,以免造成丝杠弯曲,影响传动精度和运动的灵活性,降低使用寿命。故安装时,尤其要注意丝杠的轴心线与螺母座移动轨迹的平行,并使丝杠支撑轴线与螺母座轴线一致。
3. Due to the special structure of the ball screw nut, it is not suitable to bear radial load, so as to avoid the screw bending, affecting the transmission accuracy and movement flexibility, and reducing the service life. Therefore, during installation, special attention should be paid to the parallelism of the axis line of the lead screw and the movement track of the nut seat, and make the central axis of the screw support consistent with the central axis of the nut seat.
4.将丝杠安装于设备上,注意不能使丝杠与螺母分离,以免滚珠脱出。安装时不要敲打滚珠丝杠副,尤其注意保护滚珠导管,因其管壁教薄,碰撞变形将使钢球流动受制约。
4. Install the lead screw on the equipment. Pay attention not to separate the screw from the nut, so as to prevent the ball from falling out. When installing, do not knock the ball screw pair, pay special attention to protect the ball guide tube, because the tube wall is thin, collision deformation will restrict the flow of steel ball.
以上就是导轨丝杠为大家介绍关于滚珠丝杠的相关内容,希望能够帮助到大家。如需了解更多相关资讯,请继续关注我们网站http://www.jngongrun.com  后续将呈现更多精彩的内容
The above is the guide screw for you about the ball screw related content, I hope to help you. For more information, please stay tuned to our website http://www.jngongrun.com   More wonderful content will be presented later

济南共润科技有限责任公司